|
Based on the highly successful Overdrive Supreme SLX, (favorably reviewed in the February Guitar Player Magazine), the Triple Drive Supreme features three foot
switchable channels of clean, mean and scream. Available in 50,100 and 150 watt versions, the TDS features a dedicated chime filled “California Clean Channel” with brite, deep,
and rock/jazz switches, as well as mid and gain boosts. Its second and third channels are based on our successful Overdrive Supreme clean and mean channels. The amp is controlled
by a 6-way footswitch (included), which provides channel switching, as well as independent control of mid and gain boosts for both channels. An extra (separate) footswitch jack
for the reverb is also available, as is the artist footswitch option.
The amp features 4, 8 and 16 ohm outputs, a full-time all-tube buffered effects loop with series or parallel operation.
Like the Overdrive Supreme, the loop features separate send and return level controls, a series/parallel switch and a trim control to permit line or pedal level
device interface. The loop inputs and outputs are “live” whether the loop is terminated or not. This means the send output may be used as a line out, and the return input may
be used as a spare line level input for a keyboard, drum machine, or other signal input, at any time. The reverb features a spacious Accutronics long decay 6-spring reverb driven
by a push-pull current drive amp and an ultra low noise return amp using bi-fet op-amp technology. Fully adjustable input and output levels. Like the ODS, the Tripledrive features
fan cooling, an aircraft grade T-6 aluminum chassis, individual tube bias adjusts and regulated B+ and DC preamp tube filaments for lowest noise and consistent performance despite
line noise or variations.
The chassis (like all Fuchs products) is aircraft grade aluminum; our internal construction is mixed PC board and hard wired. A detachable power cord is standard.
By using single point grounding, a regulated and buffered high voltage preamp power supply, the amp is dead quiet and free of hum at all operating levels.
 TDS Head
Front Panel features
Channel One: brite, deep, rock/jazz, high, mid, low, (with pull mid and gain boosts), Low control pulls for manual channel switch.
Channel Two: brite, deep, rock/jazz, high, mid, low, (with pull mid, and gain boosts), Channel Three: Overdrive input control (sets amount and sensitivity of distortion), Overdrive
Out (sets level when overdrive is activated). OD out control pulls for manual overdrive activation.
Master output section: Master volume (controls channels 2 and 3 only), accent, and reverb master.
TDS Rear Panel Features
IEC International standard power connector for detachable power cord.
Fuse holder. AC Power, Standby, Ground polarity, power amp “Response” switch (adjusts output stage sag at high volumes). 4, 8 16 ohm outputs, FX loop, send level control, send
output jack, return level control return input jack, series/parallel switch, effects loop trim control (sets operating level of loop for pedal or line level devices).
Footswitch Jacks
6-pin XLR connector for remote control of mid and gain boosts (for each channel) as well as channel selection (standard). ¼ footswitch jack for reverb disconnect. Artist footswitch
(optional), permits, global mute, fx loop bypass, and reverb bypass. A single guitar input and separate 4, 8 and 16 ohm outputs on ¼” Cliff jacks are provided.
¾” solid wood cabinet with durable tolex covering.
Anodized aluminum chassis with long-lasting silk screened labeling on rear panel. Front panel is brushed aluminum and available in black or silver. Crème or black knobs are available.
Heavy duty Cliff brand jacks. Solid metal shaft Alpha potentiometers. Ultra-long-life neon pilot lamp and heavy duty AC power, standby, and ground switches. Power stage features
AC balance control, and separate bias controls for each power tube.
Size:
Head: 8" tall, 27.5" wide
and 10.50" deep
Combo: 20" tall, 27.5" wide
and 11.00" deep
Weight (Head):
50 Watt 40 lbs
100 Watt 45 lbs
150 Watt 50 lbs
|
Weight (Combo):
50 Watt 112 60 lbs
50 Watt 212 75 lbs
100 Watt 112 65 lbs
100 Watt 212 80 lbs
150 Watt 112 75 lbs
150 Watt 212 90 lbs
|
Tube compliment:
5 X 12AX7 preamp tubes
2 X 6L6 power tubes (50 Watt)
4 X 6V6 (custom 50 version)
4 X 6L6 tubes (100 Watt version)
4 X 6550 (150 Watt version)
|
Power output:
50, 100 or 150 watts RMS into 4, 8, or 16 ohms.
Input Impedance -1 Meg.
FX Loop:
Output impedance 1-K. Signal; level up to 3 volts p/p Return impedance 100-K sensitivity from 250 mv to 3 volts p/p.
|
|
